By Imran Ashraf Khan
HYUNDAI HU-D25A percent S3P8849XZZ-A089 chassis 5N11.
Entering the service at the same time, press the toggle switch and VOL + and VOL-- on the TV panel.
search "MENU" .Processor LC863322B.
To enter MENU - three times pressing the hidden key in the remote (the lowest right).
Switching the MENU is done by pressing the MUTE key.
Other switching and selection of parameters (+), (-) channels, (+), (-) loudness.
Pressing the hidden key twice in the remote control (the lowest right one) is on the screen: B / W BALANCE S-BRI - 76 when you press the MUTE key in this case - a thin horizontal strip in the center of the screen to adjust the geometry.
Exit the menu - hidden key in the remote (the lowest right).
Chassis 5Y19 H-TV2910SPF percent LA76938N 7N
entrance to the service-hidden button in the remote control. HU-TV2121 percent N403 KALORA HHEN16MD01. Video LA76810A
The lowest hidden button, (to the right of the chip) is pressed once, FACTORY will be displayed.
Next P + and P- switch options.
Hyundai H-TV2902PF chassis EC6510T
1. Enter the service menu: press the buttons of the remote control "SM", INFO (square with a cross) and "CH I / II" sequentially.
2. Enter the required submenu:
geometry - buttons "1" and (or) "2",
white balance - button "3",
options 1 - button "4", options 2 - button "5".
3. Parameter selection: "PROG +" and "PROG -" remote control buttons.
4. Change the value of the parameter: the "VOL +" and "VOL -" buttons on the remote control.
5. Enter the setting mode G2: button "0" remote control. 6. Exit from the G2 setup mode: the "PROG -" button on the remote control.
Simultaneous exit from G2 mode and service menu is allowed (item 7).
7. Exit the service menu: the INFO button (square with a cross) on the remote control.
C2910, C2519, C2988
1. Set the volume - 0
2. Press the "MUTE" button on the remote control
3. While holding the "MUTE" button, press the "MENU" button on the front panel of the TV.
4. On the screen in the right corner the letter "D" will light up, and in the left corner the adjustable parameter and its value will light up.
5. Menu pages are changed with the "CAL" button.
Switching of parameters is made by green and red buttons on the blue field of the remote control.
H-LCD2000
Press MENU and STANDBY simultaneously to enter the service mode
Press MENU again.
HYUNDAI H-TV2910PFS - 5Y19
Entering the service menu TV opening the top cover of the remote control.
The sticker on the remote control is better not to remove, but to disassemble the remote control.
Under the label there are no hidden buttons, there is no also a rubber band on this button (see photo) mode "FACTORY".
OPERATION WITH THE SERVICE MENU
1. Switching in the service mode is carried out on all pages by the buttons "0" downwards and "9" upwards
2. Press the "P +" or "P-"
buttons to select the "SWITCH" line 3. Adjust the modes with the "Vol +" buttons or "Vol-" remote control 0806-RC1345-19
4. Pressing the "PROD" button - entering the service
5. 2nd press - kn. "PROD", and k. MUTE - reg. accelerating
6. Press the 3-second kn. "PROD" - MENU 0ggles the menu. MUTE (MENU 0-22)
7. 4th press - BUS OPEN
8. 5th press - exit the service
9. Then all the options in the service instructions in the tech. documentation.
HYUNDAI HU-D25A percent S3P8849XZZ-A089 chassis 5N11.
Entering the service at the same time, press the toggle switch and VOL + and VOL-- on the TV panel.
search "MENU" .Processor LC863322B.
To enter MENU - three times pressing the hidden key in the remote (the lowest right).
Switching the MENU is done by pressing the MUTE key.
Other switching and selection of parameters (+), (-) channels, (+), (-) loudness.
Pressing the hidden key twice in the remote control (the lowest right one) is displayed on the screen:
B / W BALANCE S-BRI-76 when pressing the MUTE key in this case
- a thin horizontal strip in the center of the screen to adjust the geometry.
Exit the menu - hidden key in the remote (the lowest right).
Chassis 5Y19 H-TV2910SPF percent LA76938N 7N
entrance to the service-hidden button in the console.
HU-TV2121 percent N403 KALORA HHEN16MD01. Video LA76810A
The lowest hidden button, (to the right of the chip) is pressed once, FACTORY will be displayed.
Next P + and P- switch options.
By Imran Ashraf Khan
Hyundai H-TV2902PF chassis EC6510T 1.
Enter the service menu: press the buttons of the remote control "SM", INFO (square with a cross) and "CH I / II" sequentially.
2. Enter the required submenu: geometry - buttons "1" and (or) "2", white balance - button "3"
options 1 - button "4", options 2 - button "5".
3. Parameter selection: "PROG +" and "PROG -" remote control buttons.
4. Change the value of the parameter: the "VOL +" and "VOL -" buttons on the remote control.
5. Enter the setting mode G2: button "0" remote control.
6. Exit from the G2 setup mode: the "PROG -" button on the remote control. Simultaneous exit from G2 mode and service menu is allowed (item 7).
7. Exit the service menu: the INFO button (square with a cross) on the remote control.
C2910, C2519, C2988
1. Set the volume - 0
2. Press the "MUTE" button on the remote control
3. While holding the "MUTE" button, press the "MENU" button on the front panel of the TV.
4. On the screen in the right corner the letter "D" will light up, and in the left corner the adjustable parameter and its value will light up.
5.
Switching of parameters is made by green and red buttons on the blue field of the panel.
Change the parameters in the yellow and blue buttons on the blue field.
H-LCD2000
To enter the service mode, simultaneously press <MENU> and <STANDBY> Press MENU again.
HYUNDAI H-TV2910PFS - 5Y19
Enter the TV service menu to hide the top cover of the remote control.
The sticker on the remote control is better not to remove, but to disassemble the remote control.
Under the label there are no hidden buttons,
there is no also a rubber band on this button (see photo) mode "FACTORY".
WORKING WITH THE SERVICE MENU
1. Switching in the service mode is carried out on all pages by the buttons "0" downwards and "9" upwards.
2. Use the buttons "P +" or "P-" to select the line "SWITCH"
3. Adjust the modes with the buttons "Vol +" or "Vol-" remote control 0806-RC1345-19
4. Press the "PROD" button - enter the service.
5. 2nd press - the button. "PROD", and k. MUTE - reg. accelerating.
6. Press the 3-second kn. "PROD" - MENU 0 Switching the menu of the book. MUTE (MENU 0-22).
7. Press the 4th BUS BUS .8. 5th click - exit the service.
9. Further all the options for the service instructions in those. documentation.
HYUNDAI H-TV1400, H-TV1401, H-TV21OOPF, H-TV21O1 Chassis 3Y11 SANYO
Remote control Hyundai BC-1202A
Processor IC001 LA8633XX.
Service menu: Press in sequence from the remote control [MENU], [MENU], [Q.VIEW], [MUTE].
Switching modes is the [SLEEP] button.
Exiting the service menu is the [MENU] button
HYUNDAI HU-D25A percent S3P8849XZZ-A089 chassis 5N11.
Entering the service at the same time, press the toggle switch and VOL + and VOL-- on the TV panel.
search "MENU" .Processor LC863322B.
To enter MENU - three times pressing the hidden key in the remote (the lowest right).
Switching the MENU is done by pressing the MUTE key.
Other switching and selection of parameters (+), (-) channels, (+), (-) loudness.
Pressing the hidden key twice in the remote control (the lowest right one) is on the screen: B / W BALANCE S-BRI - 76 when you press the MUTE key in this case - a thin horizontal strip in the center of the screen to adjust the geometry.
Exit the menu - hidden key in the remote (the lowest right).
Chassis 5Y19 H-TV2910SPF percent LA76938N 7N
entrance to the service-hidden button in the remote control. HU-TV2121 percent N403 KALORA HHEN16MD01. Video LA76810A
The lowest hidden button, (to the right of the chip) is pressed once, FACTORY will be displayed.
Next P + and P- switch options.
Hyundai H-TV2902PF chassis EC6510T
1. Enter the service menu: press the buttons of the remote control "SM", INFO (square with a cross) and "CH I / II" sequentially.
2. Enter the required submenu:
geometry - buttons "1" and (or) "2",
white balance - button "3",
options 1 - button "4", options 2 - button "5".
3. Parameter selection: "PROG +" and "PROG -" remote control buttons.
4. Change the value of the parameter: the "VOL +" and "VOL -" buttons on the remote control.
5. Enter the setting mode G2: button "0" remote control. 6. Exit from the G2 setup mode: the "PROG -" button on the remote control.
Simultaneous exit from G2 mode and service menu is allowed (item 7).
7. Exit the service menu: the INFO button (square with a cross) on the remote control.
C2910, C2519, C2988
1. Set the volume - 0
2. Press the "MUTE" button on the remote control
3. While holding the "MUTE" button, press the "MENU" button on the front panel of the TV.
4. On the screen in the right corner the letter "D" will light up, and in the left corner the adjustable parameter and its value will light up.
5. Menu pages are changed with the "CAL" button.
Switching of parameters is made by green and red buttons on the blue field of the remote control.
H-LCD2000
Press MENU and STANDBY simultaneously to enter the service mode
Press MENU again.
HYUNDAI H-TV2910PFS - 5Y19
Entering the service menu TV opening the top cover of the remote control.
The sticker on the remote control is better not to remove, but to disassemble the remote control.
Under the label there are no hidden buttons, there is no also a rubber band on this button (see photo) mode "FACTORY".
OPERATION WITH THE SERVICE MENU
1. Switching in the service mode is carried out on all pages by the buttons "0" downwards and "9" upwards
2. Press the "P +" or "P-"
buttons to select the "SWITCH" line 3. Adjust the modes with the "Vol +" buttons or "Vol-" remote control 0806-RC1345-19
4. Pressing the "PROD" button - entering the service
5. 2nd press - kn. "PROD", and k. MUTE - reg. accelerating
6. Press the 3-second kn. "PROD" - MENU 0ggles the menu. MUTE (MENU 0-22)
7. 4th press - BUS OPEN
8. 5th press - exit the service
9. Then all the options in the service instructions in the tech. documentation.
HYUNDAI HU-D25A percent S3P8849XZZ-A089 chassis 5N11.
Entering the service at the same time, press the toggle switch and VOL + and VOL-- on the TV panel.
search "MENU" .Processor LC863322B.
To enter MENU - three times pressing the hidden key in the remote (the lowest right).
Switching the MENU is done by pressing the MUTE key.
Other switching and selection of parameters (+), (-) channels, (+), (-) loudness.
Pressing the hidden key twice in the remote control (the lowest right one) is displayed on the screen:
B / W BALANCE S-BRI-76 when pressing the MUTE key in this case
- a thin horizontal strip in the center of the screen to adjust the geometry.
Exit the menu - hidden key in the remote (the lowest right).
Chassis 5Y19 H-TV2910SPF percent LA76938N 7N
entrance to the service-hidden button in the console.
HU-TV2121 percent N403 KALORA HHEN16MD01. Video LA76810A
The lowest hidden button, (to the right of the chip) is pressed once, FACTORY will be displayed.
Next P + and P- switch options.
By Imran Ashraf Khan
Hyundai H-TV2902PF chassis EC6510T 1.
Enter the service menu: press the buttons of the remote control "SM", INFO (square with a cross) and "CH I / II" sequentially.
2. Enter the required submenu: geometry - buttons "1" and (or) "2", white balance - button "3"
options 1 - button "4", options 2 - button "5".
3. Parameter selection: "PROG +" and "PROG -" remote control buttons.
4. Change the value of the parameter: the "VOL +" and "VOL -" buttons on the remote control.
5. Enter the setting mode G2: button "0" remote control.
6. Exit from the G2 setup mode: the "PROG -" button on the remote control. Simultaneous exit from G2 mode and service menu is allowed (item 7).
7. Exit the service menu: the INFO button (square with a cross) on the remote control.
C2910, C2519, C2988
1. Set the volume - 0
2. Press the "MUTE" button on the remote control
3. While holding the "MUTE" button, press the "MENU" button on the front panel of the TV.
4. On the screen in the right corner the letter "D" will light up, and in the left corner the adjustable parameter and its value will light up.
5.
Switching of parameters is made by green and red buttons on the blue field of the panel.
Change the parameters in the yellow and blue buttons on the blue field.
H-LCD2000
To enter the service mode, simultaneously press <MENU> and <STANDBY> Press MENU again.
HYUNDAI H-TV2910PFS - 5Y19
Enter the TV service menu to hide the top cover of the remote control.
The sticker on the remote control is better not to remove, but to disassemble the remote control.
Under the label there are no hidden buttons,
there is no also a rubber band on this button (see photo) mode "FACTORY".
WORKING WITH THE SERVICE MENU
1. Switching in the service mode is carried out on all pages by the buttons "0" downwards and "9" upwards.
2. Use the buttons "P +" or "P-" to select the line "SWITCH"
3. Adjust the modes with the buttons "Vol +" or "Vol-" remote control 0806-RC1345-19
4. Press the "PROD" button - enter the service.
5. 2nd press - the button. "PROD", and k. MUTE - reg. accelerating.
6. Press the 3-second kn. "PROD" - MENU 0 Switching the menu of the book. MUTE (MENU 0-22).
7. Press the 4th BUS BUS .8. 5th click - exit the service.
9. Further all the options for the service instructions in those. documentation.
HYUNDAI H-TV1400, H-TV1401, H-TV21OOPF, H-TV21O1 Chassis 3Y11 SANYO
Remote control Hyundai BC-1202A
Processor IC001 LA8633XX.
Service menu: Press in sequence from the remote control [MENU], [MENU], [Q.VIEW], [MUTE].
Switching modes is the [SLEEP] button.
Exiting the service menu is the [MENU] button
